Substrate Identification & Anti-Slip Dwell Protocol
This is the complete do-it-yourself kit guide. Chemical anti-slip treatments modify surface silica (μ-porosity). Select your floor type below to determine the exact required product variant and reaction dwell window — then follow the kit contents, 4-step application guide, and calibrated micro-patch pilot test.
Check a loose spare tile or transition threshold edge to confirm the body.
Verify if the pattern is a thin top glaze or runs through the entire tile.
Assigned Chemistry
--
Application Parameter
--
Reaction Termination
Neutralize with TENI Friction Stop to freeze the etch.
→ What to do after receiving your TENI-GRIP Ultra
Your TENI-GRIP Ultra DIY Kit arrives ready for self-application. Unpack it and verify every item listed in Step 1 — What's Inside the Kit is present. Gather a clean bucket, clean tap water, three clean mops and the supplied application pads, then follow the steps in order: read the exact dilution ratios (Step 2), always run the calibrated micro-patch pilot test first (Step 3), and only then apply to the whole floor (Step 4).
1 Step 1: What's Inside the Kit
Everything needed to apply the Ultra treatment like a professional — 250 mL covers approx. 30 sq. ft for self-application (120 sq. ft Pro Combo also available).
Precision sub-micron silica etchant with gloss-preserving kinetic buffers. Ultra P for vitrified porcelain & granite; Ultra C for standard glazed ceramic.
Heavy-duty wax and transit residue stripper. Removes factory protective wax coats before treatment.
Rapid alkaline reaction quencher that raises surface pH above 7.0 and locks in target traction.
For standardized 10 × 10 cm micro-patch test calibration on your lot.
For streak-free, uniform liquid film spreading across the treatment area.
Protective hand PPE for safe chemical handling during application.
2 Step 2: Prepare Your Working Dilutions Before You Start
Mix both concentrates with clean tap water before you begin your treatment. The exact ratios are critical:
-
1TENI-Prewash Concentrate (1:5 dilution):
Add 5 times water to 1 part Prewash concentrate in a clean bucket and mix well.
-
2TENI Friction Stop Concentrate (1:1 dilution):
Add 1 time water to 1 part Friction Stop concentrate in a clean bucket and mix well.
3 Step 3: Calibrated Micro-Patch Pilot Test Protocol (10 × 10 cm)
Select your formulation below to view its tailored 3-patch testing protocol. Avoid raw droplet tests: perched droplets concentrate etchant 10× faster at the focal point. Always spread a calibrated 2.0 mL volume across a full 10 × 10 cm footprint to match real-world mop dosage (100 mL/m²).
Clean & Outline Test Patches
Thoroughly clean a spare tile or inconspicuous corner using TENI-Prewash (1:5 dilution). Mark three adjacent 10 × 10 cm squares (100 cm² each) using masking tape or a grease pencil.
Apply Calibrated 2.0 mL Dosage & Spread
Using a graduated pipette or syringe, deposit exactly 2.0 mL into Patch 1 and immediately spread it into an even liquid film across the entire 10 × 10 cm square using a Chemical-Resistant foam applicator. Repeat sequentially for Patch 2 and Patch 3.
Timed Neutralization
Halt etching at each target window by flooding the patch with TENI Friction Stop (1:1 dilution with water):
Patch 1
2.0 mL / 100 cm² 1 – 2 MinutesNeutralize with TENI Friction Stop at the targeted mark.
Patch 2
2.0 mL / 100 cm² 3 – 4 MinutesNeutralize with TENI Friction Stop at the targeted mark.
Patch 3
2.0 mL / 100 cm² 5 – 6 MinutesNeutralize with TENI Friction Stop at the targeted mark.
After flooding with TENI Friction Stop and wiping dry:
1. Traction Check: Wet the patches with tap water and firmly slide a wet shoe sole or palm across each square. Note where required grip engages.
2. Optical Check: View the dry tile at a shallow 20°–30° angle against light reflections. Select the shortest dwell time that achieves required grip with zero specular clouding or glaze hazing.
4 Step 4: Whole floor application steps
The complete whole-floor job chronology — from pre-wash to a floor that's safe for foot traffic.
-
STEP 1
Surface Pre-Wash
Dilute TENI-Prewash (1:5 with water) and scrub the floor thoroughly to remove transit wax, soap scum, and oils. Rinse with clean water and dry completely.
-
STEP 2
Calibrated Micro-Patch Test
Wet-test each patch with your palm or shoe to select the optimal dwell time that gives maximum grip with zero hazing. The full protocol is in Step 3 above.
-
STEP 3
Full Area Application
Decant the TENI-GRIP Ultra solution into a clean, empty plastic bucket or container. Take a clean flat mop, dip it into the solution, and mop it evenly across the tile surface to form a continuous, uniform wet sheet (100 mL/m²). Maintain continuous surface wetness throughout the entire selected dwell window — re-mop lightly if any section begins to dry.
-
STEP 4
Reaction Neutralization & Rinse
Flood the floor immediately with TENI Friction Stop (1:1 dilution with water) to halt chemical action instantly. Squeegee off and flush thoroughly with clean tap water. The floor is immediately safe for foot traffic.
-
STEP 5
Three Clean Mops
You will need three clean mops. 1 for cleaning the floor using TENI Prewash, 1 for applying the TENI-GRIP Ultra, and 1 for applying the TENI Friction Stop.
* Crucial Application Rules
-
1Pre-Wash to Remove Factory Transit Wax:
New tiles often carry protective factory wax coats. Scrub first with TENI-Prewash (1:5 dilution) to clear coatings; otherwise, etching will be uneven.
-
2Never Use Beaded Droplet Tests:
Stationary drops concentrate active bifluoride ions over a tiny footprint and etch up to 10× faster than full floor applications. Always spread 2.0 mL across a calibrated 10 × 10 cm patch to evaluate true dwell kinetics.
-
3Maintain a Continuous Wet Liquid Sheet:
Never allow the chemical solution to dry on the surface during the treatment window. Re-spread immediately if dry patches or streaks develop.
-
4Mandatory Neutralization with TENI Friction Stop:
Plain water dilution slows down the acid but does not immediately halt microscopic etching. Applying TENI Friction Stop (1:1 dilution with water) raises surface pH above 7.0 instantly, locking in target traction.
▶ Watch the Know-How Video
See the anti-slip floor treatment applied in practice before you start.
Q Share This Guide
Scan this QR code with your phone to open the full guide anywhere.
Links directly to this application guide on your phone — handy on site when you're applying the treatment.
Full guide Kit contents + 4-step process Substrate dwell matrix Micro-patch pilot testReady to treat your floor?
Buy the kit or book a professional TechNanoIndia application with documented SCOF results.